Répondre à : Gros problèmes avec Xubuntu

#7184

Pecoflyer
Participant

voici le retour de smartctl

pecoflyer@PCDAD-UP:~$ sudo smartctl -s on -a /dev/sdb
[sudo] Mot de passe de pecoflyer : 
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-104-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10
Device Model:     ST3320620AS
Serial Number:    6QF4AW70
Firmware Version: 3.AAE
User Capacity:    320.072.933.376 bytes [320 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Mon Jan 15 18:48:01 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 249)	Self-test routine in progress...
					90% of test remaining.
Total time to complete Offline 
data collection: 		(  430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 115) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   118   075   006    Pre-fail  Always       -       179143269
  3 Spin_Up_Time            0x0003   097   095   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   092   092   020    Old_age   Always       -       8796
  5 Reallocated_Sector_Ct   0x0033   094   094   036    Pre-fail  Always       -       249
  7 Seek_Error_Rate         0x000f   084   060   030    Pre-fail  Always       -       237477075
  9 Power_On_Hours          0x0032   093   093   000    Old_age   Always       -       6798
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   091   091   020    Old_age   Always       -       9368
187 Reported_Uncorrect      0x0032   001   001   000    Old_age   Always       -       47189
189 High_Fly_Writes         0x003a   064   064   000    Old_age   Always       -       36
190 Airflow_Temperature_Cel 0x0022   057   045   045    Old_age   Always   In_the_past 43 (Min/Max 32/43 #5)
194 Temperature_Celsius     0x0022   043   055   000    Old_age   Always       -       43 (0 12 0 0 0)
195 Hardware_ECC_Recovered  0x001a   063   056   000    Old_age   Always       -       31459009
197 Current_Pending_Sector  0x0012   096   094   000    Old_age   Always       -       97
198 Offline_Uncorrectable   0x0010   096   094   000    Old_age   Offline      -       97
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 268 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 268 occurred at disk power-on lifetime: 4896 hours (204 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 2f 63 0e e0  Error: UNC at LBA = 0x000e632f = 942895

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 28 63 0e e0 00      00:55:52.450  READ DMA EXT
  c8 00 08 a8 ec dd ea 00      00:55:52.442  READ DMA
  ca 00 60 00 cc ef ec 00      00:55:52.429  WRITE DMA
  35 00 00 00 c8 ef e0 00      00:55:52.366  WRITE DMA EXT
  27 00 00 00 00 00 e0 00      00:55:52.350  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 267 occurred at disk power-on lifetime: 4896 hours (204 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 2f 63 0e e0  Error: UNC at LBA = 0x000e632f = 942895

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 28 63 0e e0 00      00:55:48.304  READ DMA EXT
  c8 00 08 b0 ec dd ea 00      00:55:48.200  READ DMA
  27 00 00 00 00 00 e0 00      00:55:48.200  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:55:48.200  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:55:48.193  SET FEATURES [Set transfer mode]

Error 266 occurred at disk power-on lifetime: 4896 hours (204 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 2f 63 0e e0  Error: UNC at LBA = 0x000e632f = 942895

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 28 63 0e e0 00      00:55:48.304  READ DMA EXT
  ea 00 00 27 63 0e a0 00      00:55:48.200  FLUSH CACHE EXT
  25 00 08 20 63 0e e0 00      00:55:48.200  READ DMA EXT
  35 00 08 88 93 c4 e0 00      00:55:48.200  WRITE DMA EXT
  ea 00 00 1f 63 0e a0 00      00:55:48.193  FLUSH CACHE EXT

Error 265 occurred at disk power-on lifetime: 4896 hours (204 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 2f 63 0e e0  Error: UNC at LBA = 0x000e632f = 942895

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 00 63 0e e0 00      00:55:45.001  READ DMA EXT
  35 00 00 00 c4 ee e0 00      00:55:44.985  WRITE DMA EXT
  35 00 00 00 c0 ee e0 00      00:55:44.977  WRITE DMA EXT
  35 00 00 00 bc ee e0 00      00:55:44.960  WRITE DMA EXT
  35 00 00 00 b8 ee e0 00      00:55:44.952  WRITE DMA EXT

Error 264 occurred at disk power-on lifetime: 4880 hours (203 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 94 66 0e e0  Error: UNC at LBA = 0x000e6694 = 943764

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 90 66 0e e0 00      00:09:19.639  READ DMA EXT
  25 00 08 88 66 0e e0 00      00:09:19.639  READ DMA EXT
  25 00 40 e8 66 0e e0 00      00:09:19.622  READ DMA EXT
  25 00 20 c8 66 0e e0 00      00:09:19.613  READ DMA EXT
  25 00 20 a8 66 0e e0 00      00:09:19.613  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      6752         -
# 2  Short offline       Completed without error       00%      6520         -
# 3  Short offline       Completed without error       00%      6516         -
# 4  Short offline       Completed without error       00%      4871         -
# 5  Short offline       Completed without error       00%      4405         -
# 6  Short offline       Completed without error       00%      4002         -
# 7  Short offline       Completed: read failure       90%      3837         30857537
# 8  Short offline       Completed: read failure       90%      3837         30857537
# 9  Short offline       Aborted by host               20%      3708         -
#10  Short offline       Completed: read failure       10%      1712         297706883
#11  Short offline       Completed without error       00%       496         -
#12  Short offline       Self-test routine in progress 90%      6798         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

pecoflyer@PCDAD-UP:~$